Общи препоръки към потребителите на InstalSystem 4, който започват работа с InstalSystem 5
| Продукт | InstalSystem 5 |
| Вид статия | TYPICAL PROBLEM |
| Актуално съдържание за версия | GOLD Rev. 15.1 |
Description
In comparison to InstalSystem 4, the InstalSystem 5 package has been built with new components. As a result, regardless of our efforts to minimize the differences in design methodology, access to tools, functions, keyboard shortcuts etc., first steps in a completely new interface may create some problems to Users accustomed to InstalSystem 4. This is why whe have decided to create this article, based on our experience from trainings and everyday contact with our Users, which should help you migrate to the newest generation of our software.
Tips and hints
General
- Calculating modules, which in InstalSystem 4 were a separate application (Instal-therm, Instal-san, Instal-OZC), have become integrated in a one multimodular application InstalSystem 5 Edytor. Turning on of all modules (Изчислителни раздели (модули) tab in Общи данни) adequately to the target scope of project causes turning on of all necessary components for the modules, such as:
- data tabs in Общи данни
- editing scope tabs in 2D редактор and 3D изглед
- tabs and messages in Диагностики
- groups and icons on the ribbon, which hinder orientation and prolong project editing.
For this reason, sequential turning on of calculating modules being subject of a given project phase is recommended.
- By default, the big calculator launches all calculations for all enabled modules (according to the settings in Изчислителни раздели (модули) in Общи данни). With the calculator used with its default function, calculation results presented in room labels are crossed off until all diagnostics messages considered as errors displayed in Диагностики have been removed. It is recommended to turn off a module or a given calculation scope, whis is not subject of a given scope of project.
- InstalSystem 4 calculation options have been transferred in InstalSystem 5 to Общи данни. Thanks to this solution, the User has access to all general data in one place.
Graphics edition
- Editing scopes of different heating installation types have been separated. Designing a given installation type (heating, floor, ceiling), you have to choose a proper editing scope (respectively: Конвекция, Лъчисти подове, стени, Лъчисти тавани)
- Installation distribution elements (Генератор на топлина и студ, Участък, Колектори itp.) may be edited on more than one editing scope.
Констуркция на сграда
- In InstalSystem 5, structural layer of the building (walls, ceilings, roofs etc.) has been distinctively separated from the layer containing partitions necessary for building thermal calculations. It is visible in separate editing scopes: Конструкция and H&E as well as in separate calculating scopes: Изчисление на сградна конструкция and Топлинни изчисления на сграда.
Walls may be multistorey, ceilings are inserted in the whole building outline (in InstalSystem 4, it was necessary to insert ceilings separately in each room), it is also possible to cut holes in the ceiling. The building structure preparation phase is much more similar to the actual process of building creation, what accelerates it and renders it more intuitive. It also allows faster and easier elimination of project errors occurred at the primary phases of project realisation. . - InstalSystem 5 is not equipped with (often giving incorrect or incomplete results) the mechanism interperting vertical structural partitions (walls, windows, doors) from DWG/DXF formats (instead, it is possible to use the Автоматични стени, плочи и покриви function - it is the recommended way of creating a building structure). Nevertheless, it is possible to perform interpretation in InstalSystem 4, save the project file (*.isb) and open it in InstalSystem 5 in order to further edit the project.
За повече информация, моля вижте: Preparation of building structure
Топлинни изчисления на сграда
- The basis to perform complete and correct calculation results are:
- lack of error messages in Диагностики in tabs: Констуркция на сграда andТоплинни изчисления на сграда
- lack of messages with the following content: Има помещения в проекта, които не бяха създадени автоматично.
- The program automatically generates heat partitions on the basis of the created building structure after having launched calculations with the Изчисление на сградна конструкция scope enabled.
Calculation of design heat load of rooms
Отоплителни системи
- InstalSystem 5 introduces a new element: Отоплителна/Охладителна зона, which may contain one or more elements such as Отоплително-охлаждаща повърхност (corresponding with Подово отопление and Отоплителна стена known from InstalSystem 4).
За повече информация, моля вижте: Heating/cooling zone - There is no logical differentiation of the elements Участък and Тръбна серпентина. They have been integrated and indicated with one common icon named Участъци. Differentiation is made automatically by the program upon the analysis of pipe feed connections and of a given unit, to which the element is connected.
- The main element used to connect manifolds with Отоплителна/Охладителна зона is Трасе на тръбни серпентини.
За повече информация, моля вижте: Pipe feeds route and editing pipe feeds in a radiant system - The element Трасе на тръбни серпентини should be connected to the edge of the element Отоплителна/Охладителна зона, and not to the element Отоплително-охлаждаща повърхност (pipe feeds to particular О/Охл. под are generated automatically).
- Manifold accessories (e.g. mixing unit, ball valve sets etc.) are added to the manifold by choosing proper catalogue type (window: Общи данни, tab: Колектори, фигинги и контрол, field: Колекторен вентил)
За повече информация, моля вижте: Manifold and accessories - The basic element which connects systems among various floors is Вертикален клон.
За повече информация, моля вижте: Connecting storeys with the "Stack" element